Rufus clean and converts the drive everytime I think. But since I have no problem to boot in uefi with Windows 7 I don't think it's related with my problem since. Windows 7, Windows Server 2003 R2 (32-Bit x86), Windows Server 2003 R2 x64 editions, Windows Server 2008, Windows Server 2008 R2, Windows Vista, Windows XP Service Pack 3. How to Install Windows 7 over a Network using Linux – PXE, DNSMasq, and Samba . So if you plan to install Windows XP or Linux using this tutorial. The project also includes MEMDISK, a tool to boot legacy operating systems (such as DOS) from nontraditional media; it is usually used in conjunction with PXELINUX and ISOLINUX. As of Syslinux 3. ISO images. What is this crap? If wading through Microsoft’s horrid technet site doesn’t work for you. By default, all tools are installed at C: \Program Files\< version> \Tools, where < version> can be Windows OPK or Windows AIK. At the command prompt, run the Copype. The script requires two arguments: hardware architecture and destination location.
For example,copype. Where < arch> can be x. For example,copype. This option requires that you create an . Oscdimg tool. On your technician computer, create an . Oscdimg. At a command prompt, type: oscdimg - n - bc: \winpe. If you are not familiar with SYSLINUX, read the SYSLINUX FAQ first, since this documentation only explains the differences. On the TFTP server, create the directory “/tftpboot”, and copy pxelinux. SYSLINUX distribution) and any kernel or initrd images that you want to boot. Finally, create the directory “/tftpboot/pxelinux. The configuration file (equivalent of syslinux. SYSLINUX FAQ for the options here) will live in this directory. Because more than one system may be booted from the same server, the configuration file name depends on the IP address of the booting machine. PXELINUX will search for its config file on the boot server in the following way: 1) First, it will search for the config file using the hardware type (using its ARP type code) and address, all in lower case hexadecimal with dash separators; for example, for an Ethernet (ARP type 1) with address 8. AA: BB: CC: DD it would search for the filename 0. Next, it will search for the config file using its own IP address in upper case hexadecimal, e. C0. 00. 02. 5B (you can use the included progam gethostip to compute the hexadecimal IP address for any host). If that file is not found, it will remove one hex digit and try again. Ultimately, it will try looking for a file named default (in lower case). As an example, if the boot file name is /mybootdir/pxelinux. Ethernet MAC address is `8. AA: BB: CC: DD` and the IP address 1. Inside the TFTP boot directory is a folder we named pxelinux. I specify to mount the Samba share as the ! With a little more work you can take elements of this tutorial and create a cheap linux box that upgrades all your Windows clients in a few hours over the weekend. Install Windows 7 From USBThis guide works 1. Windows 7 and Windows 8 unlike most of the guides out there. I have seen many sites/blogs that have “Install Vista from USB guide” but either with incomplete steps or not working guide. I have also seen some guides that don’t’ use proper commands in this guide. After spending many hours I have come up with this 1. Windows 7 and Windows 8 from USB flash drive. I just did this method on one of my friends machine and installed Windows 7 and Windows 8 . The main advantage is that by using USB drive you will be able to install Windows 7 or Windows 8 in just 1. You can also use this bootable USB drive on friend’s computer who doesn’t have a DVD optical drive. The method is very simple and you can use without any hassles. Needless to say that your motherboard should support USB Boot feature to make use of the bootable USB drive. And if your PC doesn’t support booting from USB, you can still install Windows from USB by following our how to install Windows 7/8 from USB drive even if your PC doesn’t support USB boot feature. How to install Windows 1. USB drive guide might also interest you. Requirements: USB Flash Drive (Minimum 4. GB)Windows 7 or Windows 8 installation files. Follow the below steps to create bootable Windows 7/Windows 8 USB drive using which you can install Windows 7 or Windows 8 easily. Procedure: Step 1: Plug- in your USB flash drive to USB port and move all the contents from USB drive to a safe location on your system. Step 2: Open Command Prompt with admin rights. Use any of the below methods to open Command Prompt with admin rights.*Type cmd in Start menu search box and hit Ctrl+ Shift+ Enter. Or*Go to Start menu > All programs > Accessories, right click on Command Prompt and select Run as administrator. Step 3: You need to know about the USB drive a little bit. Type in the following commands in the command prompt: First type DISKPART and hit enter to see the below message. Next type LIST DISK command and note down the Disk number (ex: Disk 1) of your USB flash drive. In the below screenshot my Flash Drive Disk no is Disk 1. Step 4: Next type all the below commands one by one. Here I assume that your disk drive no is “Disk 1”. If you have Disk 2 as your USB flash drive then use Disk 2. Refer the above step to confirm it. So below are the commands you need to type and execute one by one: SELECT DISK 1 CLEANCREATE PARTITION PRIMARYSELECT PARTITION 1. ACTIVEFORMAT FS=NTFS Quick(In the above command, replace NTFS with FAT3. UEFI)(Format process may take few seconds)ASSIGNEXITDon’t close the command prompt as we need to execute one more command at the next step. Just minimize it. Step 5: Next insert your Windows. Windows 8 DVD into the optical drive and check the drive letter of the DVD drive. In this guide I will assume that your DVD drive letter is “D” and USB drive letter is “H” (open my computer to know about it). Step 6: Maximize the minimized Command Prompt in the 4th step. Type the following command now: D: CD BOOT and hit enter. Where “D” is your DVD drive letter. CD BOOT and hit enter to see the below message. Step 7: Type another command given below to update the USB drive with BOOTMGR compatible code. BOOTSECT. EXE /NT6. H: Where “H” is your USB drive letter. Once you enter the above command you will see the below message. Step 8: Copy your Windows 7 or Windows 8 DVD contents to the USB flash drive. Step 9: Your USB drive is ready to boot and install Windows 7 or Windows 8. Only thing you need to change the boot priority at the BIOS to USB from the HDD or CD ROM drive. I won’t explain it as it’s just the matter the changing the boot priority or enabling the USB boot option in the BIOS. Note: If you are not able to boot after following this guide means you haven’t set the BIOS priority to USB. If you got any problem in following this guide feel free to ask questions by leaving comment. Update on Jan 1. 1, 2. If you find this guide difficult to follow, please use the easy- to- use guide to create a bootable USB to install Windows 7 or Windows 8 using official tool. This guide works 1. Windows 8/8. 1 as well. Make sure you follow all steps correctly and launch the Command Prompt with admin rights (as given in the guide) to avoid errors.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
September 2017
Categories |